我用的是FC4＋华为ｓｍａｒｔ ｍｘ８１０ｕｓｂ－ａｄｓｌ猫上的网，在红旗上装不上驱动，只能用FC4了，好在能认出我的ｕｓｂ猫
我是电话加装ａｄｓｌ，独享的1.5ｍ的带宽
可是问题来了，装了ｒｐ－ｐｐｐｏｅ3.5
在ｄｎｓ项由于不知道本地ｄｎｓ所以添了ｓｅｒｖｅｒ
其余设置好后，运行ａｄｓｌ－ｓｔａｒｔ，显示２行：
Ｉｎｖａｌｉｄ ｅｔｈｅｒｎｅｔ ｉｎ ｐｏｒｃｈｅｔ6388
下一行好像是提示超时
用ａｄｓｌ－ｓｔａｔｕｓ，显示：
adsl-status
ink is down (can't read pppoe PID file /var/run/pppoe.conf-adsl.pid.pppoe
用ｉｆｃｏｎｆｉｇ －ａ，显示：
eth0 Link encap:Ethernet HWaddr 00:11:5B:20:16:06
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:11 Base address:0xd000
eth1 Link encap:Ethernet HWaddr 00:73:04:21:5E:2C
inet6 addr: fe80::273:4ff:fe21:5e2c/64 Scope
ink
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:12 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:2604 (2.5 Ki b
lo Link encap
ocal Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:1674 errors:0 dropped:0 overruns:0 frame:0
TX packets:1674 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1337604 (1.2 Mib TX bytes:1337604 (1.2 Mib
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
看也看不出门道，冥思苦想好几天，实在不行
请诸位英雄高手帮忙解决！
